PETLIN (MALAYSIA) SDN BHD C478s3s-T>

PRODUCT DATA SHEET PETLIN

PETLIN LD MOSOX Low Density Polyethylene

PETLIN LD MOSOX is a low density polyethylene resin designed primarily for injection moulding applications. It is produced by the state-of-the-art DSM Stamicarbon tubular process. It contains antioxidant (BHT free) additives.

Characteristics low gels, high flq~ high gloss, high filler acceptance. .

Applications lids, housewares, masterbatches; powder coating.

Extrusion Conditions for injection moulding : recommended melt temperature 180-210°C.

Typical Data

Properties Units Typical values Test methods

Pol~mer grogerties :

Melt Flow Rate: dg/min 50 ISO 1133 Density kg/m3 919 ISO 1183 (A)

Me!;hani!;gl gro12erti~s :

Hardness Shore D 43 ISO 868

Stress at yield N/mm2 8 ISO R527-2 ~tress at break N/mm2 7 ISO R527-2 Strain at break % 200 ISO R527-2 Modulus of elasticity N/mm2 168 ISO R527-2

Creep modulus ISO 899 after 1 hr N/mm2 73 after 1000 hr N/mm2 38

Notch impact strength (Izod) ISO 180/1A at 23°C kJ/m2 41 at -30°C kJ/m2 5

Thermal grogerties :

Vicat Softening Temperature oc 78 ISO 306 Melting Point (DSC) oc 104 DIN 53765

Misc. 12rogerties :

ESCR hr 0.5 DSM Method

The properties shown above are typical values and are not to be taken as specifications.

Food contact approval status :

This material complies with FDA 21 CFR 177.1520 when used unmodified and according to good manufacturing practices for food contact applications. Accordingly, this material may be used in all food contact applications (except holding food during cooking).

IMPORTANT NOTICE : Information contained in this document is accurate and reliable to the knowledge and belief of Petlin (Malaysia) Sdn Bhd. The suggestions and recommendations are offered herein as a guide in the use of Petlin products, and cannot be guaranteed because the conditions of use are beyond Petlin's control. Petlin assumes no responsibility for the use of infonmation supplied, the application, adaptation or processing of its products described herein and hereby disclaims all liability in regard to such use.

20040608 Version no. : 03

PETLIN {MALAYSIA) SON BHD(478535-T)

PRODUCT DATA SHEET (PRELIMINARY) PET LIN

PETLIN LD C150Y Low Density Polyethylene

PETLIN LD C150Y is a low density polyethylene resin for general purpose and thin film applications. It is produced by the state-of-the-art DSM Stamicarbon tubular process. It contains slip, antioxidant (BHT free) and antiblack additives. It is intended primarily for blown film process.

Characteristics: low gels, high drawdown, high clarity, high gloss, good sealability, high slip, high antiblocking. Applications: thin gauge films for textile, laundry, dry cleaning, garment; crosslinked foams; zip bags. Recommended gauges : 15 - 60 microns. Extrusion conditions: for blown film: melt temperature 145-165 oc and blow-up-ratio of 2 to 3: 1 are recommendable.

Typical Data : ( 25 micron blown film} Proeerties Units TY.eical value Test methods Polymer ~ro~erties: Melt Flow Rate: dg/min 5 ISO 1133 Density kg/m3 921 ISO 1183 (A) O~tical ~ro~erties:

Gloss (45°) %o 62 ASTM 02457 Haze % 7.2 ASTM D1003A Mechanical ~ro~erties: Impact strength kJ/m 15 ASTM 04272 Tear strength TO kN/m 30 ISO 6383-2

MD kN/m 80 Tensile stress at break TO MPa 15 ISO R527-1

MD MPa 27 Strain at break TO % >450 ISO R527-1

MD % 100 Modulus of elasticity TO MPa 190 ISO R527-1

MD MPa 190 Coefficient of friction 0.2 Petlin method

The properties shown above are typical values and are not to be taken as specifications.

IMPORT ANT NOTICE Information contained in this document is accurate and reliable to the knowledge and belief of Petlin (Malaysia) Sdn Bhd. The suggestions and recommendations are offered herein as a guide in the use of Petlin products, and cannot be guaranteed because the conditions of use are beyond Petlin's control. Petlin assumes no responsibility for the use of information supplied, the application, adaptation or processing of its products described herein and hereby disclaims all liability in regard to such use. 20010820 version no. : 01

ENVIRONMENT The environmental aspects of any packaging material do not only imply waste issues but have to be considered in relation with the use of natural resources, the preservations of foodstuffs etc. Petlin considers polyethylene to be an environmentally efficient packaging material. Its low specific energy consumption and insignificant emissions to air and water designate polyethylene as the ecological alternative in comparison with the traditional packaging materials.

Petlin LD low density polyethylene, as supplied, can be recycled, incinerated or disposed of in landfill without detriment to the environment.

The recycling of packaging materials is supported by Petlin whenever ecological and social benefits are achieved. Whenever 'thermal' recycling of packaging (i.e. in~ineration with energy recovery) is carried out, polyethylene - with its fairly simple molecular structure and low amount of additives - is considered to be a trouble-free fuel.

SAFETY Under normal conditions, polyethylenes do not present a toxic hazard through skin contact or inhalation. During processing, contact with molten polymer and inhalation of volatile fumes should be avoided. It is recommended to install exhaust hoods over processing machines and to keep working area well ventilated. More specific information on the safety aspects of the Petlin LD low density polyethylene is provided in the relevant Material Safety Data Sheets, available from Petlin's sales agents.

STORAGE As polyethylenes, like most polymers, are combustible, the usual precautions concerning ignition sources should be taken in warehouses and storage rooms. It is necessary to observe the normal rules for orderly and safe handling and to keep out dust, direct sunlight and moisture.

Further information is available from : PETLIN (MALAYSIA) SON BHD (478535-T) Level 14, Tower 1, PETRONAS Twin Towers Kuala Lumpur City Centre 50088 Kuala Lumpur, Malaysia

REV. 20110601

Pro

du

ct

Da

ta s

he

et

1102K

Description:

1102K is a Polypropylene Homo-polymer resin for extrusion process with the characteristic

of good stiffness and good impact. It is suitable for mono-filament and yarn, too. It also

meets the F.D.A. requirement in the code of federal regulations in 21 CFR 177.1520 for

food contact.

Typical applications;

Mono-filament / Yarn : rope, stretch tape, coarse textile for woven bag and tarpaulin

Extrusion : straw, sheet, industrial board

Physical Properties: Method Unit Value

Melt Flow Index (2.16 kg/230⁰C) ASTM D1238 g/10min. 4

Tensile Strength at Yield ASTM D638 N/mm2 37

Elongation at Yield ASTM D638 % 27

Charpy Notched Impact Strength (at 23⁰C) DIN 53453 mJ/mm2 4.5

Flexural Modulus (1% SECANT) ASTM D790 MPa 1600

Rockwell Hardness ASTM D785 R-Scale 107

Heat Distortion Temperature (Load 0.45 N/MM2) ASTM D 648 ⁰C 110

Processing Technique

Processing Temperature : 200 – 280 °C

**However, the actual processing conditions depend on mold design, power of machine, equipment and

other environments.**

Remark: The values presented on the above are typical laboratory average, not to be construed as specifications and may vary within moderate ranges. The applicability or the accuracy of this information or the suitable of our products cannot be guaranteed because the conditions of use on the part or our uses are beyond our control.

Polypropylene (PP)

REV. 20110601

Pro

du

ct

Da

ta s

he

et

1100NK

Description:

1100NK is a Polypropylene Homo-polymer for injection molding process with high flow

and good stiffness characteristic. It is suitable for the production of general part, long

path and thin wall, such as house-ware, closure, food container and etc. It also meets

the F.D.A. requirement in the code of federal regulations in 21 CFR 177.1520 for food

contact.

Physical Properties: Method Unit Value

Melt Flow Index (2.16 kg/230⁰C) ASTM D1238 g/10min. 11

Tensile Strength at Yield ASTM D638 N/mm2 36

Elongation at Yield ASTM D638 % 26

Charpy Notched Impact Strength (at 23⁰C) DIN 53453 mJ/mm2 2.9

Flexural Modulus (1% SECANT) ASTM D790 MPa 1500

Rockwell Hardness ASTM D785 R-Scale 107

Heat Distortion Temperature (Load 0.45 N/MM2) ASTM D 648 ⁰C 110

Processing Technique

Processing Temperature : 190 – 240 °C

**However, the actual processing conditions depend on mold design, power of machine, equipment and

other environments.**

Remark: The values presented on the above are typical laboratory average, not to be construed as specifications and may vary within moderate ranges. The applicability or the accuracy of this information or the suitable of our products cannot be guaranteed because the conditions of use on the part or our uses are beyond our control.

Polypropylene (PP)

REV. 20110601

Pro

du

ct

Da

ta s

he

et

Description:

Typical applications;

Physical Properties: Method Unit Value

Melt Flow Index (2.16 kg/230⁰C) g/10min.

2

Charpy Notched Impact Strength (at 23⁰C)

Heat Distortion Temperature (Load 0.45 N/MM2) ⁰C

Processing Technique

Processing Temperature : 180 – 240 °C

Remark: The values presented on the above are typical laboratory average, not to be construed as specifications and may vary within moderate ranges. The applicability or the accuracy of this information or the suitable of our products cannot be guaranteed because the conditions of use on the part or our uses are beyond our control.

Polypropylene (PP)

11 75SM

1175SM is a Homo polymer Polypropylene for extrusion coating.

Characteristics

It is suitable for coating woven bags and tarp aulins.

; Good extrudability,Good adhesive,Good clarity,Low neck in,High speed

Extrusion coating It also meets the F.D.A. requirement in the code of federal regulations in 21CFR 177.1520

ASTM D1238 35

ASTM D 648 100

Tensile Strength at Yield ASTM D638 N/mm 30

Flexural Modulus (1% SECANT) ASTM D790 MPa 1200

DIN 53453 mJ/mm2 2

Elongation at Yield ASTM D638 % -

Rockwell Hardness ASTM D785 R-Scale -

**However, the actual processing conditions depend on machine, equipment and other environments.

U.A.E Office LB182202/03, Jebel Ali, Dubai P.O.Box 261539 United Arab Emirates

Tel: 00971 4 885 7724‐7 Fax:     00971 4 885 7723 Email: polymer@pccint.com

Product Description HF 5110 is a high molecular weight high density polyethylene.

Applications HF 5110 is suitable for Extrusion, film, blown, bags and density modifies.

Typical data

Test method Unit Value Properties

ISO 1183 kg/m3 951 Density

ISO 1133 dg/min 10 MFR (190°C/21.6kg)

ISO527-1,2 MPa 1050 Tensile Modulus

ISO 527-1,3 MPa 55 Tensile Strength(MD)

ISO 527-1,3 MPa 55 Tensile Strength(TD)

ISO 527-1 % 580 Tensile Strain at Break(MD)

ISO 527-1 % 620 Tensile Strain at Break(TD)

ISO 527-1 MPa 26 Tensile Stress at Yield

ISO 527-1 % 10 Tensile Strain at Yield

ISO 6383-2 mN 250 Elemendorf tear strength(MD)

ISO 6383-2 mN 800 Elemendorf tear strength(TD)

ISO 3146 °C 132 Melting Point

ISO 306 °C 127 Vicat Temp,(A50,50°C/h,10N) The above data are typical laboratory average . They are intended to serve as guides only Film properties taken from 20 μm blown film extruded at a melt temperature of 220°C, long stalk process, and a blow-up ratio of 4:1. Additive: Antioxidant – Heat stabilizer - Zinc Stearate

Producer: Arya Sasol Petrochemical Co. Licensor: Basell

Processing Recommended film thickness: 15 to 50 μm.

Packaging Supplied in pellet form and can be packaged in 25Kg Bags, one ton semi bulk or 17 tons bulk containers.

HF5110 High Density Polyethylene

Product Data Sheet

Petrochemical Commercial Co. International Ltd. 

Film

Note: this information is based on our current knowledge and experience .in view of many factors that may affect processing and application, this data does not relive processors from the responsibility of carrying out their own tests and experiments, neither does it imply any legally binding assurance of certain properties or of suitability for a specific purpose. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed.

Food packaging HF 5110 meets the relevant requirements of plastics directive 2002/72/EC (06-08-2002) and its amendments till directive 2008/39EC relating to plastic materials and articles intended to come into contact with foodstuffs. Pharmaceutical Application HF 5110 meets the requirements of the European pharmacopeia version 6 section 3.1.5 for pharmaceutical application. Conveying Conveying equipment should be designed to prevent accumulation of fines and dust particles can, under certain conditions, pose an explosion hazard. We recommend that the conveying system used: 1. be equipped with adequate filters 2. is operated and maintained in such a manner to ensure no leaks develop 3. that adequate grounding exists at all times We further recommended that good housekeeping will practiced throughout the facility Storage As ultraviolet light may cause a change in the material, all resins should be protected from direct sunlight and/or heat during storage. The storage location should also be dry, dust free and the ambient temperature should not exceed 50. It is also advisable to process polyethylene resins (in pelletized or powder from) within 6 months after delivery, this because also excessive aging of polyethylene can lead to a deterioration in quality

Handling Minimal protection to prevent possible mechanical or thermal injury to the eyes. Fabrication areas should be ventilated to carry away fumes or vapors. Combustibility Polyethylene resins will burn when supplied adequate heat and oxygen. They should be handled and stored away from contact with direct flames and/or other ignition sources .in burning; polyethylene resins contribute high heat and may generate a dense black smoke. Fires can be extinguished by conventional means with water and mist preferred. In enclosed areas, fire fighters should be provided with self contained breathing apparatus.

Product Data Sheet

Petrochemical Commercial Co. International Ltd. 

HHHDDDPPPEEE PPPAAALLLLLLEEETTT RRREEESSSIIINNN

TAISOX HDPE 8041 Resin for Injection Molding

台塑烯台塑烯台塑烯台塑烯 HDPE 8041 棧板棧板棧板棧板專用料專用料專用料專用料

臺灣塑膠工業股份有限公司臺灣塑膠工業股份有限公司臺灣塑膠工業股份有限公司臺灣塑膠工業股份有限公司 聚烯事業部聚烯事業部聚烯事業部聚烯事業部

台塑烯台塑烯台塑烯台塑烯 HDPE 8041 棧板棧板棧板棧板專用料專用料專用料專用料

一、產品描述

台塑烯 HDPE 8041為低壓製程所生產的高密度聚乙烯。

8041具有良好的耐衝擊強度、剛性及耐低溫脆性等特性。

8041主要用於塑膠棧板，亦可用於大型搬運箱、運動護具、工業容器、工業用安全帽等產品。

二、基本性質

單位 檢驗方法 數值

基本物性

熔融指數 MI2.16 g/10min ASTM D1238 4.0 密度 g/cm3 ASTM D1505 0.960

熱性質 熔點 ℃ 台塑 DSC 133

脆化溫度 ℃ ASTM D746 <-70

軟化點 ℃ ASTM D1525 127

機械性質 拉力降伏強度 Kg/cm2 ASTM D638 310

拉力斷裂強度 Kg/cm2 ASTM D638 250

拉力斷裂伸長率 ％ ASTM D638 1000

彎曲模量 Kg/cm2 ASTM D790 12500

艾式衝擊強度 Kg-cm/cm notch ASTM D256 8

硬度 Shore D ASTM D2240 70

耐環境應力龜裂 Hours ASTM D1693 6

*以上資料為測試平均值，僅提供參考

三、加工建議 8041用於一般射出成型製品時，建議加工溫度使用 180±10℃；若使用於較大型製品如棧板，

建議加工溫度使用 210±10℃。

四、法規符合 符合 FDA 21 177.1520.規定： 符合美國食品、藥品之包裝或容器規定 符合 RoHS 2011/65/EU： 不含重金屬、PBBs 及 PBDEs 符合 REACH SVHC： 符合 151項限用物質規定 符合 EU-10： 符合歐盟食品之包裝或容器規定 符合 EN-71： 符合歐盟對玩具製品重金屬含量規定 詳細資料及證明書： http://www2.fpc.com.tw/PE/indexc.htm

五、包裝 25Kg PE內襯紙袋與 1 噸裝太空包。

六、儲存 於通風良好儲存溫度 40℃以下﹑無陽光直射處，可儲放 3年。

臺灣塑膠工業股份有限公司 聚烯事業部 http://www2.fpc.com.tw/PE/indexc.htm

TAISOX HDPE 8041 Resin for Pallet

1. Product description 8041 is high density polyethylene resin made by low pressure slurry process.

8041 has good balance of stiffness and impact strength.

8041 is designed for pallets, also suitable for large crates, containers, industrial helmet etc.

2. Typical properties Units Test Method Typical Value Properties

Melt Index MI2.16 g/10min ASTM D1238 4.0

Density g/cm3 ASTM D1505 0.960 Thermal properties

Melting point ℃ FPC DSC 133

Brittleness point ℃ ASTM D746 <-70

Softening point ℃ ASTM D1525 127

Mechanical properties Tensile strength at yield Kg/cm2 ASTM D638 250

Tensile strength at break Kg/cm2 ASTM D638 310

Elongation at break ％ ASTM D638 1000

Flexural Modulus Kg/cm2 ASTM D790 12500

Izod Impact Strength Kg-cm/cm notch ASTM D256 8

Hardness Shore D ASTM D2240 70

ESCR Hours ASTM D1693 6

* Data shown are average values and should not be examined for specifications

3. Processing Taisox®8041 resin is used for general injection molding products, recommended processing temperature

180 ± 10 ℃; if used for larger products such as pallets, recommended processing temperature 210 ±

10℃.

4. Regulatory status

Meet FDA 21 177.1520.： for packaging contact with food or drug

Meet RoHS 2011/65/EU： free of heavy metal , PBBs and PBDEs

Meet REACH SVHC： for 151 items of restricted substances

Meet EU-10： EU rules of packaging or container

Meet EN-71： EU rules of heavy metal content of toys

Download from WWW： http://www2.fpc.com.tw/PE/indexc.htm

5. Packaging：25Kg/paper bag or 1000Kg/bulk bag. 6. Storage：Resin better be stored at temperature under 40℃.

Sun exposure, heat, humidity better avoided. Expiration date is 3 years.

Formosa Plastics Co. Polyethylene Division http://www2.fpc.com.tw/PE/indexc.htm