Sedikit bincang bincang masalah VFO dan Xtall filter dengan Bos Blekok.

……………………………>>>>>>>>>>>>>>>>>>>>>>>>>>>

Indra S Ekoputro

Si Emprit

Suka · · Berhenti Mengikuti Kiriman · 11 Februari pukul 19:05

Indra S Ekoputro Bisa 10W dan bisa di 80M juga Om Juni, ini skema dan hasilnya, http://www.facebook.com/photo.php?fbid=193283630811724&set=o.303352739683138&type=1&theater

http://www.facebook.com/photo.php?v=4030103794184&set=o.303352739683138&type=2&theater

22 Februari pukul 7:18 · Suka · 1

3 Maret pukul 11:16 · Suka

Adi Is pak Indra.. sudah hampir rampung saya conteknyah...tapi ada beberapa pertanyaan seh sebelum di jajal neh...(satu) apa manfaat filternya kok sampe 6... lha bitx kan cuman 4 biji.....(dua)..apa nilai dari kapasitor by pass ke ground sama semua nilainya....(ketga) untuk AF amp nya pake npn disambungin ke pnp apa memang itu cara untuk mendapatkan low noise atau gain nyang kenceng..(ke empat) kok masih pake relay seh.., apa keuntungan atawa kelebihan relay dibandingkan dioda....segitu dulu..ntar kalo sudah dapet ilham atawa penjelasan nya dilanjutin ngegambar sukahati nya...., dan saya nggak ngikutin pake LM380.., lha pake 386 saja sering makan speaker kecil nya..apa lagih 1watt kekencengan...., ntar disiapin saja TDA2005 BTL pake speaker saloooon...., TQ pak.

5 Maret pukul 9:13 · Telah disunting · Suka · 1

Indra S Ekoputro Om Adi, alhamdullilah dah selesai ya.1. Kristal filter 6 pole mempunyai kelebihan dalam sisi slope dibandingkan yang 4 pole (pada BITX), pada -6db BW mungkin sama, katakanlah 2.3Khz. Tetapi akan berbeda pada -60db, 6 pole mempunyai 4.6-5Khz, sedangkan yang 4 pole bisa selebar 8-10Khz. Biasanya yang 4 pole masih kedengaran signal dari kanal kiri dan kanannya. Tetapi hilang jika pakai kristal filter > 6 pole. http://www.arrl.org/files/file/QEX_Next_Issue/Nov-Dec_2009/QEX_Nov-Dec_09_Feature.pdf2. Saya menggunakan C in/out dan bypass dengan nilai sama untuk praktis-nya saja.

3. NPN atau PNP sebetulnya sama saja. Transistor pertama digunakan sebagai low impedance input preamp (50 ohm), sedang transistor 2 & 3 sebagai low pass filter. Cona lihat kapasitor di kolektor yang di bypass ke ground (<3khz). Low noise preamp lebih mudah didapatkan dengan transistor dibandingkan IC, karena IC penguatannya sudah dibuat flat dari 0-100Khz dengan NF tertentu.4. Relay tetep masih lebih baik dibandingkan diode pin sekalipun. Alasannya nilai kontak-nya hampir 0 Ohm, sedangkan diode masih mempunyai R-on dan capacitance dengan nilai tertentu, misal 1N4148 punya R-on sekitar 30-40 ohm, 1N4007 punya R-on sekitar 8-16 Ohm, HSMP3820 (diode pin) punya R-on sekitar 1-2 Ohm.5. LM386 punya karaketristik "ngosos" yang nggak bisa dihilangkan atau distrorsi 10% , dan powernya maks 0.5W. Sedangkan LM380, punya distorsi 0.1% jika power <1W atau 10% jika >2W. Harga LM380 sebanding dengan 4x LM386. Saya malah lebih suka pakai TDA2003 atau TDA2005 BTL yang dikerjakan maksimal 2W, karena distorsi-nya cuma 0.1%.

5 Maret pukul 9:50 · Telah disunting · Suka

Dian Kurniawan om Indra S Ekoputro, bikin istilah baru "ngosos"..hehehe, punya link tentang artikel mengenai cascode amplifier yang simple itung2an mya?

5 Maret pukul 9:52 · Suka

Indra S Ekoputro Ha ha ha, kan LM386 bunyinya seperti itu, kalau nggak ada input, beda dengan LM380 atau TDA2003 Om Dian Kurniawan. Ada caranya Om Dian, coba cek ke http://www.qrp.pops.net/af-amp-2008.asp.@Om Adis, untuk bikin preamp audio yang low noise dan bisa dilihat di http://www.qrp.pops.net/AF-2010-bjt-parameters.asp dan http://www.qrp.pops.net/filter1.asp.

AF Power Amps

www.qrp.pops.net

QRP, Homebrew amateur radio receivers, transmitters & transceivers. QRP related

5 Maret pukul 10:15 · Telah disunting · Suka

Dian Kurniawan referensi kita sama Om Indra S Ekoputro, QRP POPS ini luar biasa ya.. sampe tabung untuk gitar dia maen juga hehehe

5 Maret pukul 10:05 · Suka

Dian Kurniawan Calculator nya juga mantab abis

5 Maret pukul 10:06 · Suka

Indra S Ekoputro Betul Om Dian Kurniawan. Ini site favorite saya, karena mengupas banyak ide2 sederhana dari W7ZOI dan KK7B dengan biaya murah. Blekok, prenjak, emprit dibuat dari sumber ini.

5 Maret pukul 10:09 · Suka

Adi Is Pak indra.. point satu..begitu yah..ntar di edit lagih nih gambarnya... jadi yang saya coba di 40 M..dengan xtall 10 mHz pake 4 buah dan kapasitornya 100 pF..ada yang sedang ngobrol tong kosong di 7115... eh ada keresek keresek.. coba dial.. ternyata di 7100 sedang ngetune suara.. satutuuuuuu.dua wawawa.....wah sekitaran 3 kHz up & down masih jelas suaranya.. setelah 10 kHz sudah tidak jelas..nah speleteran karena sideband nya masih lebar apa tidak bisa di besarkan nilai kapasitornya..( saya sudah buat pake varactor nilai max 250 pF..tapi belon sempet di coba..).. point empat akan saya ikutin pake relay yang 2x3....dan point lima.. di pasaran speaker kecil yang banyak ukuran nya 0.25 watt saja.. itu alasan saya tetep dengan 386 itu.., dan gain nya dikecilin saja dengan membuang elko kaki 1-8.. TQ pak... lanjutin ngegambarr..

5 Maret pukul 10:57 · Suka · 1

Indra S Ekoputro Om Adi Is, sebelum dibuat PCB-nya lebih baik ditambah jadi 6 xtal, paling cuma nambah 5 ribu rupiah. Sehingga jika tetep mau pakai 4 kristal, yang dua tingal di-jumper saja. Kalau pakai 10Mhz, impedansi In/Out ada di sekitar 160-170 Ohm. Saya selalu pakai 100pf untuk lebar 2.1-2.5Khz. Om Emprit Haji lebih seneng pakai 81pf atau 68pf, lebih lebar dan bisa nge-dungdung katanya, impedansi in/out juga naik sedikit.Jika C bypass dibesarkan, BW -6db akan menyempit, tetapi BW -60db nggak bergeser.Model Emprit TRX, kalau pakai diode agak ribet Om Adi, lebih enak pakai relay, simple, gampang, dan berkualitas he he he

5 Maret pukul 11:33 · Telah disunting · Suka

Adi Is lagi di geser geser nih komponen nya biar masuk di PCB 10 x 20 cm..

5 Maret pukul 12:48 · Suka

Adi Is pak Indra.. kalo xtall 3,579 itu yang dipake.., berapa nilai C ke ground nya... nomor ini saya banyak stock..., tapi di bfo nya geser nya sedikit sekali.., tidak sampai 1 kHz..walaupun sudah dilangsungkan ke ground..., jadi harus bagaimana agar bisa swing sekitaran 2 kHz...

5 Maret pukul 18:16 · Suka

Indra S Ekoputro Om Adi Is, Jika pakai 6x xtal 3.579Mhz, C in/out dan bypass gunakan 39pf, BW sekitar 2.6Khz, dan impedansi In/Out sekitar 1.2 kOhm.Untuk nggeser xtal ini sebesar +/- 2Khz, gunakan 2x xtal yang diparlel, lalu seri dengan induktor 45uH + trimmer 0-30pF. Jika ingin lebih dari 2Khz, tambah xtal lagi menjadi 3x parelel.Jika ingin digunakan pada BITX, jangan lupa ditambah matching impedansi 200 Ohm ke 1.2 k Ohm.

5 Maret pukul 18:24 · Telah disunting · Suka

Adi Is bongkar bongkar ada lebih seratusan ( dulunya mungkin sekantong isinya lebih seribuan..)kelihatanya presisi pak dari sekian itu tidak ada yang selisih lebih dari 100 Hz... beda denga xtall 27.000 freq dasarnya di 9.., tapi dari sratus tidak ada yang selisih 100 Hz.....sampai 1 kHz.., OK pak saya siapkan lokasinya buat di pasangin tiga untuk BFO dan enam untuk filter.., jadi main di tujuh bikin VFO di 3,500 juga.., apa tidak ada efect jeleknya kalo freq nya hampir sama di jumlahkan..?

5 Maret pukul 18:43 · Suka

Lik Gotri om Indra S Ekoputro klo xtal 4.286MHz dibikin filter pakai 4 xtal dan 5 kapasitor 47pf kira2 impedansinya berapa juga ya om?saya coba di bitx bua RX dah lumayan ga begitu ngaleng suaranya.

5 Maret pukul 18:57 · Suka

Indra S Ekoputro Om Lik Gotri, ya jelas ngaleng, impedansi-nya sekitar 900 Ohm dengan BW 2.3Khz. Kalau digunakan di BITX ya nggak cocok. Impedansi BITX sekitar 200 Ohm. Masih perlu matching impedansi. Coba pakai trik ini, mudah2an bisa membantu. R 220 ohm di kolektor yang akan masuk ke filter ganti dengan 820 ohm.Om Adi Is, nggak ada efek-nya, itu cara VXO untuk nggeser frekwensi. Saya sudah lihat di Osciloscope maupun spectrum analyzer nggak beda.

5 Maret pukul 21:12 · Telah disunting · Suka · 2

Adi Is MASIH LANJUT NANYA MASALAH FILTER INI.., sudah saya baca pak link nya ituh.., tapi ora mudeng..en mau nanya pak Indra saja lah....ada 8 xtall..C nya (semua) lebih kecil dari 50 pF.., ada keterangan 3 dB Bandwidth =2,4 dB.., riple = 0,2 dB. nah tolong jelasin secara faktual praktek saja...kamsudnya apabila monitor di sarang gajah di 7.100 itu.., dengan nilai itu hilang keresex nya sampai berapa kHz.., seperti saya dapatkan xtal 10 mHz dengan 4 xtall plus c=100 pf 10 khz keatas dan kebawah...

6 jam yang lalu · Suka

Indra S Ekoputro Om Adi Is, xtal filter BW -3db = 2.4Khz, riple = 0.2db, BW -60db = 4.8Khz (misal), dan In/Out impedance =? ohm.Saya pakai visual saja supaya mudah.1. Kristal filter BITX, BW=2.4Khz harga = US$? http://golddred.ipower.com/kc0wox/bitxsmd/ver4/crystalfiltertest4.gif2. Kristal filter Inrad, BW=2.4Khz harga US$105 http://tomnyc.no-ip.org/images/inrad2.7khzcrystalfilter.jpgJika BITX kita pakai kristal pertama, maka pada waktu kita memenrima signal S9, dan di kanal atas bawah (+/- 5Khz) juga ada signal S9, receiver kita tidak terganggu, tetapi kalau kanal atas dan bawahnya ada signal S9+40db?Bagaimana jika BITX dipasang filter kedua, anggap saja impedance In/Out sudah matched? Apakah masih terganggu?Nah, sekarang kita balik, kalau BITX kita mancar dengan filter pertama? dengan power 1W, 10W, 100W, 1KW?Kalau BITX kita mancar dengan filter kedua? dengan power 1W, 10W, 100W, 1KW?Jadi filter tidak sekedar kualitas receive, tetapi juga kualitas pada waktu transmit.Nah link di atas yg diposting terdahulu, adalah cara untuk memperbaiki xtal filter dengan cara membuat audio low pass filter yang di-cut di 2.4Khz, bisa dengan 1 oktaf (-12db), 2 oktaf (-24db), bahkan lebih.Kesimpulannya, radio yang baik ya harus mempunyai banyak filter, mulai dari LPF, BPF, Preselector (MTU), IF diplexer, kristal filter (> 6 pole), Audio diplexer, dan audio filter (SCARF).Receive bersih, transmit juga bersih.

http://golddred.ipower.com/kc0wox/bitxsmd/ver4/crystalfiltertest4.gif

golddred.ipower.com

3 jam yang lalu · Telah disunting · Suka

Adi Is QK terima kasih banyak sekali pak.. saya coba untuk memahami nya.., sekalian saya perbaiki jadi 6 xtall, sekaligus C nya pake varaktor ingin dengan sensasinya perubahan dari 30 pF s/ 300 pF.., ntar saya laporkan hasilnya..., kalo sempit.., nah itu yang di cari.....73, cugnbeberapa detik yang lalu · Suka

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

KIRIMAN TERBARU

Indra S Ekoputro

Emprit ......

Suka · · Berhenti Mengikuti Kiriman · Jumat pukul 18:33

o

o

Rudik Wid, Ariya Pramudiya, Indra S Ekoputro dan 9 lainnya menyukai ini.

o

Daryono Daryonoo audionya empuk

Jumat pukul 20:47 · Suka

o

Syafruddin oscnya bagus juga Om Indra S Ekoputro boleh juga dicoba .........bearti VCO ya......?

Jumat pukul 23:15 · Suka

o

Indra S Ekoputro Om Daryono Daryonoo. Thanks. Rahasianya ada di preamp yg pakai 4 transistor.Om Syafruddin, betul masih pakai VCO Hartley, tetapi saya pakai diode varactor.

Jumat pukul 23:29 · Suka

o

Syafruddin bisa diapload gak Om Indra S Ekoputro osc hartleynya,mau coba diaplikasikan kebitxnya

Sabtu pukul 18:48 · Suka · 1

o

Indra S Ekoputro Bisa Om Syafruddin. Ini skema umum kok. Q1 J310. Buffer pakai 2N3904.C4 nilainya 100pF ditambah diode varactor 20-39pF. C1=5pF.Agar bisa bekerja di 5Mhz, L1 = 20 lilitan pada koker 10.7Mhz yang dibuat CT 5 lilitan dari ground. Ini skemanya :http://webspace.webring.com/people/jl/leon_heller/vfo.html

VFO/BUFFER

webspace.webring.com

It's basically a standard Hartley oscillator, followed by Roy Lewallen's buffer ...Lihat Selengkapnya

Kemarin jam 7:12 · Telah disunting · Suka · 2

o

Syafruddin kalau T1 berapa lilit sama diameter toroid ama kawatnya Om,,,,,,,,?

22 jam yang lalu · Suka

o

Adi Is pak indra yang saya dapatkan.. yang tidak pernah ada yang membahas atau nyuruh... koker oscilator ituh kudu di sarungin pake logam..., kalo kagak kena RF 100 wat meliuk liuk dan buyutan tuh suaranya...

22 jam yang lalu · Suka

o

Indra S Ekoputro Untuk T1 bisa digunakan FT-37-43 atau FT-37-62 8 lilitan primer dan 3 sekunder, diameter kawat terserah asal semua gulungan bisa masuk. Jika nggak ada, bisa gunakan ferrite balun tv, tetapi saya belum pernah coba toroid lampu tl.Om Adi Is, kalau shielding untuk oscilator dan koil, kayaknya semua sudah paham, terutama di koil oscilator, kecuali pakai toroid kuning (material 6).Malah pada waktu transmit, kadang loncat ke atas atau kebawah sampai 1Khz. Kalau cuma sampai 20W, kayaknya sih masih aman Om Adi, yang penting oscilator dijauhkan dari LPF (lihat video di atas).

20 jam yang lalu · Suka

Amateur and Short Wave Radio Electronics Experimenter's Web Site

SWL Page QRP - Log Site Info & Links Junk Box Blog Guitar Amp Design Center Email Topics 1998 - 2002 Topics 2003 - 2005 Topics 2006 - 2009 Topics 2010 - 2012

VFO - 2011

Building VFOs in 2011 might seem an irrelevant exercise given the move to and evolution of digital signal generators laden with bells and whistles like memories and audio or video frequency displays.

A successful L-C VFO requires skill, patience and some good parts to pull off — else, a "drift monster" may result. Despite their limitations, it's possible to build L-C VFOs with low frequency drift, distortion and phase noise; our typical VFO performance markers. L-C VFOs don't require programming skills or equipment to encode a microprocessor — making them a good choice for people who don't build or can't afford kit oscillators. Most of all, they kindle creativity, problem solving and pride when your oscillator actually works as planned. Junk box radio; my passion.

This material reflects empiricism; not science. It's really your VFO design odyssey; a chance to think creatively and critically to sort out what works and what's folly.Countless web pages discuss VFO design and I encourage you to search for and read them. Wes' EMRFD oscillator and temperature compensation notes = essential reading.

I discuss various VFO topics and present 2 completed designs.

1. Frequency Stability

Building an oscillator that stays on frequency purports our greatest challenge and goal in L-C VFO design. Since drifting VFOs pose a source of frustration, I cover some topics that may help your VFO stay on frequency — do they help?

What is good drift parameter?

I'm uncertain, for after warm-up, I've measured kits that drifted 50-150 Hertz per hour, built L-C VFOs that drifted under 20 Hz per hour and every once and a while, build a drift monster VFO that sweeps upward at 2 - 8 hertz per minute! Likely under 20 Hertz per hour after warm up = a gold standard to compare against. You should be able to listen to a 10-20 minute QSO with no re-tuning, however, this assumes the transmitting stations are locked on frequency.

1. Unloaded Q and Frequency Stability

The number 1 reason to employ high resonator Q in oscillators is to obtain low phase noise. Secondly, the very steep phase slope through high Q resonance minimizes the effect of amplifier phase shifts caused by temperature changes and this in turn, minimizes any amplifier-induced frequency instability.

Long term frequency stability is chiefly dependent on the temperature, environmental and age stability of the resonator components regardless of Q.

I often see designs featuring high Q inductors wound on powdered iron toroids complimented with trashy, low Q variable and/or fixed capacitors, If you design for a high Q tank to minimize phase noise, consider using a high Q coil plus appropriately temperature stable, high Q capacitors.

2. Temperature Stable Inductors

Knowing that I'm venturing into a topic of great debate and lore, the inductor is 1/2 of the VFO resonator and thus a major source of temperature drift in L-C VFOs. Since MF and HF VFO designs may preclude using the inherently more temperature stable air wound inductor, powdered iron toroids dominate our evermore compact designs. Many builders choose #6 material, although the lower temperature coefficient of #7 material theoretically should be better — however, my experiments have failed to measure a significant difference between these 2.

Some builders prefer size 68 inductors, for the bigger core is less affected by heating than smaller size toroids. My experience suggests that providing the VFO amplifier current is kept low, both size 50 and 68 are suitable and the inductance needed should inform the core size.

I used to think that heavier gauge wire created greater frequency stability than smaller gauge wire until Wes, W7ZOI, woke me up. As it turns out, smaller gauge wire is often better for thermal stability because smaller gauge wire lies closer against the toroid core. Winding stiffer, heavier gauge wire creates more air gaps than smaller gauge wire and air gaps expand and contract during temperature changes. Smaller gauge wire will have a reduced Q, but it won't be as significantly lower as you might guess. As possible, I prefer tightly wound number 28 wire. 26 gauge wire tends to be my maximum size wire for VFO coils, however I suggest you make your own conclusions.

Wash your hands before winding and use both hands to actively move both the toroid and wire for tight turns. Take your time, ensure steady wire pressure and avoid kinking your wire. Taps increase the likelihood for air gaps — mitigate this by stripping the 2 tap forming wires as close to the toroid as possible and twist them into 1 wire right down tightly to the toroid edge to reduce any air gap.

The thermal stability characteristics of wire can be mitigated somewhat by annealing the wire with temperature cycling or by dunking it in boiling water. Roy, W7EL first reported annealing coils in 1980 and this has been confirmed during experiments by builders using temperature controlled ovens. I don't boil my coils any more.

Your L-C ratio sometime affects stability — a higher L to C ratio may reduce the effects of stray capacitance, but does not guarantee good outcomes.

3. Double Stacked Toroids

I noticed a new trend in VFO design is to stack 2 powdered iron toroid inductors. This allows the builder to double the inductance per number of windings over a single toroidal inductor. In an L-C VFO, the goal of these builders possibly is to reduce heating effects, increase unloaded Q, or perhaps to reduce core magnet flux density. For me the goal is far simpler, I just want to make compact, large L value inductors for 3 MHz and less.

Above — A T68-6 hamburger. The two T68-6 cores were epoxy glued together and compressed lightly in a vice for several hours. One of the initial tests I performed was to see if boiling the stacked coil affected the epoxy glue. The glue was not effected by annealing wire on a stacked coil with 5 or even 10 minutes of boiling in water. As mentioned, I stopped boiling my VFO inductors as tightly winding them with 26 gauge wire seems to work well.

I hold concern that stacked toroids may create more wire-air gaps when compared to a single toroid and stay with 1 toroid as possible. In compact antenna tuners and other non VFO projects, this isn't an issue.

4. VFO Tank Capacitors

We choose VFO tank capacitors to avoid temperature change caused frequency drift, or to counter drift during our temperature compensation process.

Many authors have published guidelines for long term temperature stability. It's important to consider these guidelines, but also try whatever works. I believe the following arguments are accurate based upon my experiments:

1. 1. Multiple NP0 or C0G (0 temperature-compensation) tank caps: Most builders minimally use 4 or more C0G or NPO capacitors to reduce heating effects and to average out temperature coefficient variations.

2.3. 2. No VFO tank capacitors from online surplus parts stores; buy new stock from

known and reputable manufacturers. Grab bags and musty, old, surplus parts can obviate good design.

4.5. 3. Trimmer and tuning caps need to be temperature stable. Air variable capacitors

= my favorite, as possible.6.7. 4. Varactor, or diode tuning generally = more drift and a greater need for

temperature compensation.8.9. 5. Employ short, stiff capacitor leads. I use 100 volt or higher voltage C0G tank

caps as they tend to have thicker leads.

5. Temperature Compensation

The goal of temperature compensation is to cancel the tendency of the VFO to drift in 1 direction — easier said than done + very time consuming. A web search for VFO temperature compensation will yield many good write-ups. I feel it's partly art, partly luck and partly science. Your net VFO temperature coefficient can be affected by so many variables, so no 1 recipe will ensure a low drift VFO. Experiment, allow a lot of time to assess your changes and be patient — you'll figure it out.

The simplest way to test for drift involves watching a frequency counter, but if you don't have one, you might use a commercial, frequency stable (synthesized) receiver set in the SSB/CW mode. I use both. Experienced builders often employ an oven to test their temperature compensation at different, controlled temperatures. Wes, W7ZOI employs a styrofoam cooler housing a light bulb heat source controlled by a Variac. See EMRFD for more details and a photograph.

In 2011, I decided to build up a supply of temperature compensation capacitors and keep them in their own parts bin.

Above — "Tempco caps". A parts drawer containing polystyrene capacitors from 10 to 270 pF plus some 56 pF ceramic N750 capacitors for negative temperature compensation. I purchased these capacitors on eBay.

For capacitors other than NP0 (which use 0 instead of a ppm value), the temperature coefficient = P for positive and N for negative, followed by a 3-digit value specifying ppm/°C. For example, N220 is - 200 ppm/°C. and P100 is +100 ppm/°C.

I use NP0 and C0G ceramic capacitors interchangeably for both tuning and RF bypassing the VFO tank resonator. For C0G bypass, I normally apply 0.001 uF, however, the more expensive 0.1 uF COG ceramic capacitors are still sold if you need bypass under 7 MHz. A tank decoupling resistor + bypass cap will widen your bypass bandwidth and deserves strong consideration. Undecoupled and unbypassed VFO DC lines will easily transmit the VFO tank energy to other stages.

If your VFO is drifting upward you might insert 1 or more positive coefficient capacitor(s). If your VFO drifts downward, then try using negative coefficient value(s). Sometimes just 1 capacitor will do the job.

Since I don't stock any positive coefficient capacitors for positive coefficient compensation, I might try a adding a silver mica capacitor. *Caution* silver mica capacitors are extremely non-predictable and can't be universally recommended in temperature compensation schemes. You might also try swapping out 1 or more of your main tank NP0 or C0G capacitors in case they are bad; sometimes it gets frustrating. I

provide some temperature compensation examples on the QRP Modules 2011 web page in the 7 MHz VCO section.

Above — 56 pF N750 ceramic capacitors rated at 1KV

6. Mechanical Rigidity

Movement of your VFO tank parts may lead to frequency instability. For example,

1. 1. Well secure your single-sided only copper board. I use at least 3 number 8 bolts — 4-40 hardware is too light. Aggressively bolt down any variable capacitors. No tank parts should move.

2.3. 2. Anchor your inductor so it cannot budge: nylon bolts, zap-straps, glue -

whatever. 4.5. 3. Consider placing the VFO in a strong chassis with rubber feet.6.7. 4. Buss wires should be made from thicker gauge, well anchored wire.

7. Miscellaneous Points

1. 1. Bypass the B+ well. Regulate the VFO amplifier DC voltage to as low as practical to keep heating down.

2.3. 2. You should have the buffer + load resistor connected to your VFO when

testing. Do your temperature stability work after the buffer is built and the VFO is in its case.

4.5. 3.Stick your VFOs in an air tight, RF tight case to minimize air temperature

changes and RF leakage respectively. Sometimes a VFO will drift once in a case because any radiated buffer amplifier heat will warm up the inside of the chassis. This usually levels off after warm up. Some builders incorrectly refer to short

term drift as the frequency drift associated with warm up — why bother? True short term stability really refers to noise content — an advanced topic.

6.7. 4. A 3 terminal regulator with a bypass capacitor may reduce noise compared to a

zener diode regulator. Specific low noise, and low output voltage temperature coefficient voltage regulators are available, but likely overkill.

8.9. 5. JFET Gate clamping diodes may increase phase noise, but not prohibitively so

in most popcorn designs. 10.11. 6. When winding toroid inductors, wind 2 extra turns. When finished, unwind the

first 2 turns since they are usually loosely wound and prime culprits for air gaps.12.13. 7. Since magnet wire comes off small spools, wire has a natural curve or radius —

ensure you wind your coils according to the natural curve of the wire.

Vackar VFO Experiments

Some builders proclaim the Vackar as the "King of VFOs". I built a couple and became impressed by the low distortion and less than 5 Hertz per hour long-term drift achieved in my 2 designs. Inspired by work from Iulian, YO3DAC entitled Very Low Phase Noise Vackar VFO for HF Transceivers (link and reference used by permission of Iulian), I crafted my version from his notes and schematic.

Above — Schematic of the Vackar VFO employing a BD139 — a large area transistor, to reduce 1/f noise. Iulian shared many design pearls in his paper and I won't repeat them. I ran Q1 with 0.4 mA emitter current to reduce heating and flicker noise. It's difficult to measure flicker noise, so no objective comments can be made.

I limited the tuning range to 34 KHz since the tuning capacitor lacked reduction gear and I was born with fumble fingers. As a CW operator - you'll find me down at the bottom of the band away from the RRTY anyhow. Increasing the 5 pF cap coupling the tuning capacitor to the tank increases the tuning range as expected.

Temperature compensating my VFO with the 5 pF silver mica capacitor proved a gamble since SM caps are unpredictable and often best avoided. In my VFO, it worked perfectly, however.

Above — The final amp and measured output data. Measuring the 2nd harmonic 36 dB down without any tuned circuit or low-pass filter rocked. I ran nearly 22 mA of emitter current to bump up the return loss and spectral purity. A 2N5109 or 2N3866 would likely do a better job with less current. Total current = the entire VFO current. I glued a drilled copper penny on the 2N2222 to dissipate heat.

A photo of my version of a Vackar VFO. My design goals included low phase noise, low distortion, a return loss over 20 dB, good reverse isolation and ~7 dBm output power. I believe all VFOs are experimental; you build to suit whatever tuning capacitor or varactors you have, plus design around constraints such as total current, tuning range and other personal criteria.

Unlike harmonic distortion, oscillator phase noise, being close to the oscillation frequency, cannot be removed by filtering nor limiting — you must design for low phase noise. Modern digital VFOs are well harmonically filtered, and any phase noise depends on the DDS clock employed, so check the DDS specifications carefully if you go the DDS VFO route.

I'll be the first to state I'm no expert with VFOs, however, likely the only way to become expert is to build many and learn from your mistakes.

Above — A 7 MHz Vackar VFO with the lid off

Sound Test?

Although this technique raises the ire of some builders, I test my VFOs in a nearby receiver. The VFO output was terminated with a 51 ohm resistor that was also attached to my frequency counter via alligator clips and wire. I tuned a nearby CW superheterodyne receiver to 7.00 MHz with the audio beat note centered in its 600 hertz wide I.F. filter and watched the counter plus listened to the receiver.

Click for a 1 minute 32 second audio file of the result. You can hear a station in the back ground despite only having a 45 cm piece of wire as the receiver antenna. The VFO slowly drifts down to 6999996 Hz and then slowly back up to 7000000 Hz. You can hear the signal amplitude decrease as the VFO drifts down. So it doesn't stay perfectly on frequency, but slowly cycles up and down a few hertz. Totally usable for on the air.

A badly drifting VFO will move out of the test receiver I.F. pass band and sound like a Theremin as it does. Testing in a receiver; places the VFO in the exact circumstance it will be used — beating RF to mix to another frequency; in this case, base band audio.

The temperature stability and compensation of any VFO schematic are rarely reproducible since there are just too many variables. Try your best to get the drift out of your VFO using low temperature coefficient capacitors (NP0/C0G) and then after that,

temperature compensate. Even today, I occasionally build a drift monster VFO and become frustrated. VFO design is not for the feint of heart and it's no wonder that many builders make a VXO, or cave in and build or buy a DDS signal generator.

2.8 - 10.5 MHz Signal Generator

I decided to build a new, general purpose ~2.8 and 10.5 MHz signal generator (SG). The first VFO topology tested was the Vackar. In my version, while employing a 100K ohm resistor as the buffer, the VFO only tuned from about 4 to 8 MHz and suffered from extreme amplitude variation as I changed the frequency across its range. For sweeping filters or measuring Q, a signal leveling circuit would be needed as normally we like our SG output to be flat across its frequency range. I later changed to a Hartley VFO because of its flatter output and the wider available frequency range with any given resonator.

This initial Vackar VFO experiment wasn't a total waste as I learned a way to accurately sweep a Device Under Test with an unlevel amplitude SG. Measure the peak-peak voltages of the DUT with a signal generator and an oscilloscope in the same manner we measure insertion loss or gain in a 50 ohm system: Measure the peak-to-peak voltage with the DUT in line; disconnect the DUT, insert a barrel connector and then re-measure.

The dBm difference between the 2 becomes the dB value to plot for that frequency. To a sweep a filter, say for example, a band-pass filter, find the center frequency and then sweep below and above that CF while plotting the dB versus frequency. This "in and thorough" measurement described takes time, but resolves any frequency versus amplitude issues and can be used to test signal generators. We tend to ignore things like cable loss versus frequency and scope or spectrum analyzer ripple.

Still, it will be easier to just use a Hartley VFO where our sweeps are assumed to be level due to the flatness of the amplitude versus frequency for small excursions such as 3 dB band-pass filter sweeps.

Above — My Hartley VFO is morphed into a double-gate MOSFET VFO; this was a mistake and I make lots of them.

When venturing out, it's often best to confirm a proven design is working before morphing it to something untried. Shown above left is the Hartley oscillator from EMRFD Chapter 7 sans buffer. Fixed "tuning" capacitors; either 20 pF (not shown) or 370 pF (150 pF + 220 pF) represent the intended high and low frequency swing of my air variable tuning capacitors.

I wanted a variable amplitude VFO and thus replaced the JFET with a double-gate MOSFET using a simple variable voltage divider to control gate 2. I showed this to Wes, W7ZOI and he informed me that the flicker noise of MOSFETs precludes their use in oscillators. I have always wondered why I've never seen MOSFET VFOs in any radio literature.

Above — My project chassis fitted with hardware. I employed 2 air variable tuning capacitors — the fine tuning capacitor ranges 13.6 to 27.5 pF, features built in 6:1 reduction gear and was purchased from Doug DeMaw many years ago. I secured the main copper board with 6 number 8 bolts. Rubber feet provide a stable, shock resistant base for the sheet metal box.

Final Build

Above — Oscillator + buffer schematics of the final version of my signal generator. I spent 1 evening playing with VFO designs and settled on the simple Hartley from EMRFD, Figure 7 .27. The 3 turn link provided lower distortion than coupling the oscillator to its buffer by the JFET source or gate.

Regulated 12.2 VDC powers the oscillator; avoiding the typical 5-9 VDC voltage regulator we normally use. 1 hour drift lies under 50 Hertz. The Q2/Q3, Q4 and Q5 transformer inductances were optimized to allow good signal and/or matching performance in the ~ 2.5 to 10.5 MHz frequency range.

A hybrid cascode (hycas) buffer with variable base bias on Q2 forms the amplitude control for both the high impedance and low impedance outputs. The 510 ohm gate resistance on Q4 terminates the hycas amplifier and sets up a known output impedance to drive the 50 ohm feedback amp. I measured a greater than 22 dB return loss on the output of the 19:6 turn transformer from 4 to 14 MHz — indicating it drives the feedback amp reasonably well.

Above — The 50 ohm impedance feedback amp. Running 25.1 mA current allowed a clean sine wave output up to 2.12 volts-peak to peak into a 50 Ω terminated oscilloscope, plus a return loss of over 30 dB across the SG tuning range. 3 sample return loss measurements are shown including an out of range 14 MHz assessment.

S22 = negative of return loss.

Two series resistors made up the 37 ohm "resistor" depicted in the 6 dB pad, although a 39 Ω resistor would work fine. The maximal signal amplitude fell off at about 9 MHz, but did not drop below 9 dBm at the maximum frequency.

Above — A "lid off" front panel photograph. Click or click for other photos. I'm now using miniature pots with a shaft diameter of 3.18mm. The potentiometer shaft lacks a knob and I'll purchase some on my next parts order.

Above — The completed signal generator.

Above — Signal generator output at 3.5 MHz.

I appreciate that the VFO tank would be difficult to replicate since the 2 air variable capacitors are unique, however this is true of most VFOs. Wes wrote some great notes in EMRFD Chapter 7 regarding copying signal generators and the versatility of the Hartley VFO. I hope this project furnishes some ideas that spawn you to build something better than I did. (I've received lots of feedback indicating many builders have built some great VFOs - Way to go!)

Miscellaneous Bits

Above — Scope traces of an unbuffered Hartley oscillator with a X10 scope probe across a 51 ohm resistor across the 3 turn link. The unbuffered Hartley sine wave isn't harmonic free, but cleans up when properly buffered with a higher impedance amplifier. Figure A = the lowest frequency (2.7 MHz) — the distortion increased with frequency (Figure B was measured at 10.5 MHz). Figure C illustrates how slightly stronger output coupling with a 6 turn link trashes the output waveform — the strategy of using 2-3 links over the center of the main inductor works well.

Figure D is the 6 link coupled Figure C oscillator with the gate clamping diode removed; yikes! I spent 4 hours studying what different current, voltages, coupling and so forth do to the Harley oscillator. I recommend the Hartley topology because it's simple, always starts and versatile.

Above — In my various signal generator experiments, I zap strapped the toroid to a small piece of thick copper board that was later soldered to the main board. The L seems robustly secured.

Above — A stacked toroid from the deleted VFO-2008 web page. I incorporated some of the information from the VFO-2008 page into this web page

Above — In order of preference, 3 ways to couple a Hartley oscillator to its buffer. From now on, I'll couple with a 1-3 turn link since it gave a lower distortion signal than with source or gate coupling. This figure omits the gate clamping diode seen earlier— tapping the inductor as shown keepings the FET gate AC voltage at a reasonable level when not using a gate clamping diode. Some builders leave off the gate clamp diode that clips positive signal peaks for lower phase noise. The diode acts as an AGC and offers benefit. Reverse biasing this diode was suggested by Dr. Ulrich Rohde: see — Key Components of Modern Receiver Design - Part 2: Dr. Ulrich Rohde, KA2WEU , QST for June 1994.

A formula to use for the inductor taps: Divide the total turns by 1.45 to get the first tap and by 7.25 to get the second tap (near ground link).

Enjoy your VFO experiments.