fizik q4 -
TRANSCRIPT
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 2/11
PART A
10 Objective Questions. Answer all the questions .
1. Which is a base unit :
A AmpereB NewtonC JouleD Degree Celsius
2. Which of the following prefixes arranged in ascending order is
correct?
A Giga, mega, kilo, nanoB Kilo, nano, giga, megaC Kilo, mega, nano, gigaD Nano, kilo, mega, giga
3. which of the following error is a systematic error?
A Error due to the position of the eye not vertically
above the mark being readB Error due to the zero marks of the scales of the
vernier calipers not coinciding when the two
jaws are tightly closed.C Error due to the over tightening of the anvil
while turning the spindle of the micrometer
srewgauge.
4. which of the following statement is correct about the zero error?
A It can be reduced by taking repeated
measurements using the same instruments.
2
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 3/11
B It can be reduced by finding the average value
of all reading from the same measurement.C It becomes smaller if the range of the scale of
the instrument is sufficiently large.
D It can be eliminated by checking the scales of instrument before measurement and then
making adjustments to the readings taken
5. which of the following steps can help eliminate a parallax error
while taking voltage reading from a voltmeter?
A Take repeated readings and calculate their
average value.B Use voltmeter which has a plane mirror under
the pointer.C Take voltmeter readings with the aid of the
magnifying glass.D Choose a more sensitive voltmeter.
6. which of the following measurement is obtained by using a pair
of vernier calllipers?
A 29.3 mmB 293 dmC 2.93 mmD 0.293 cm
7. which instruments are most suitable for the accurate
measurement of the thickness of coin and the internal diameter
of a beaker?
Thickness of coin Internal diameter of
beakerA Metre ruler Micrometer screw gaugeB Vernier callipers Micrometer screw gauge
3
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 4/11
C Vernier callipers Metre ruleD Micrometer screw gauge Vernier calipers
8. Which of the following describes a scalar quantity?
A The acceleration of a bullet trainB The barking force needed to stop a track.C The amount of heat to boil 1000 cm3 of water.D The thrust needed to launch a rocket.
9. Which of the following phenomenon cannot be explained by
physics concepts?
A The formation of the rainbowsB The ebb and flow of the tidesC The ability of the chameleon to change to the colour
of the surroundings.D A pen appears bent in a glass of water.
10. which of the following devices is not a contribution of
Physic?
A Jet engineB Bionic limbs
C BiodieselD LCD television set
PART B :
3 structured questions. Answer all questions. Write your
answers in the spaces provided in the questions papers.
1. Base Quantities are
……………………………………………………………
……………………………………………………………………………………
4
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 5/11
……………………………………………………………………………………
……
Base Quantity symbol SI UnitLength L Metre, m
2. Express the quantities below using prefixes and scientific
notation:
Quantities Prefixes Scientific Notation
384 000 000 m 384 Mm 3.84 x 108 m57 000 m km86 000 000 000s Gs0.000 002 34g µg0.004 A mA0.000 000 088 nm
3. Convert the following to the stated units:
2.56 Gm= m 2.35 km = mm
435 mm = cm 3 x 104 Mm = km
5
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 6/11
2m2 = mm2 3 cm3 = mm3
1.2 gcm-3 = kgm-3 8.2 kmh-1 = ms-1
6
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 7/11
Figure 1
4. Figure 1 shows a measuring device.
(a) Name the physical quantity measured by the device.
[1mark]
_______________________________________________________________________
_
(b) What is the reading shown by the device?
[1mark]
_______________________________________________________________________
_
(c) Explain how you would check for the zero error of this device.
[1mark]
_______________________________________________________________________
_
d) What is the value of the smallest division on the scale?
[1 mark]
7
8/3/2019 FIZIK Q4 -
http://slidepdf.com/reader/full/fizik-q4- 10/11
5. Figure 2 shows a vernier calipers used to measure the external
diameter of a hollow PVC pipe.
(a)(i) Name the part labelled Y.
[1 mark]
_______________________________________________________________
(ii) What is the function of Y?
[1 mark]
____________________________________________________________
The external diameter of the PVC pipe is measured at four
different places, the readings are recorded in the table
(b) Why is the external diameter measured four times?
[1 mark]
__________________________________________________________ c) what is the value of the smallest division on the scale?
[ 1 mark]
OBJECTIVE ANSWER :
QUESTION
1 A B C D2 A B C D
3 A B C D4 A B C D5 A B C D6 A B C D7 A B C D8 A B C D9 A B C D10 A B C D
10