marking scheme engineering technology.doc
Post on 22-Jan-2016
225 Views
Preview:
TRANSCRIPT
SULIT 3764/1 & 23764/1 &2 TeknologiKejuruteraan
SEKTOR SEKOLAH BERASRAMA PENUHBAHAGIAN SEKOLAH
KEMENTERIAN PELAJARAN MALAYSIA
PEPERIKSAAN PERTENGAHAN TAHUN TINGKATAN 4 / 2006
SKEMA PEMARKAHANKERTAS 1 & 2
SKEMA DIAGNOSTIK UPT F4 2006Section A
01. Engineering Technology is a scientific study of converting natural resources into tools and machines which eventually will fulfill the needs and demands of ever-changing society.
(3 marks)
02. i) Increase in the employment opportunities.ii) Activate manufacturing industry.iii) Service providers such as banking and insurance transaction.iv) Will result in the increase of the country’s revenue.
(Relevance= 4 marks)
03. i) Medium ii) Total work system (2 marks)04. C, A & B (3 marks)05. 3, 1, 4 & 2 (4 marks)06. i) Testing ii) Holding\Clamping iii) Driving (3 marks)07. i) Calculation must be shown (4.00 + (18 x 0.18)) = 4.18 mm
ii) A = Anvil B = Barrel / Hub(2 marks)(2 marks)
08.
21.02 mm
(2 marks)
09. i) M = Metric Unit, 15 = Major Diameter & 1.25 = Thread Pitchii) Drill size (Calculation shown) = 15 – 1.25 = 13.75 mm
(3 marks)(1 mark)
10. 1, 4, 2 & 3 (4 marks)11. A = False, B = False, C = True & D = True (4 marks)12. i) A ii) C iii) B (3 marks)13. Any two from list:
i) High compression strength ii) Durable iii) Water tightiv) Can be casted iv) Fairly low tensile strength
(2 marks)
14. Thermoplastic Thermosetting Plastic- Can become soft when
reheated to be moulded to other shapes.
- Durable, soft.- Become soft & may melt at
a temperature 93ºC.
Any two from list = (2 marks)
- Cannot be remoulded to other shapes through reheating process.
- Rigid, hard & strong (compared to thermoplastic) & fairly brittle.
- Can withstand high temperature up to 260 ºC.
Any two from list = (2 marks)
(4 marks)
15. (i) Human with machine (ii) Machine with machine (iii) Machine with human
(3 marks)
16. 47kΩ ± 20% (i) Yellow (ii) Violet (iii) Orange (3 marks)17. Select three only:
(i) The number of windings or turns of the coil.(ii) The diameter of the coil.(iii) The type of the core.(iv)The length of the coil.
(3 marks)
18. (a)
(b)
(3 marks)
(1 mark)
(1 mark)
(1 mark)
19.Pp = Ps = 2400W (1m)
Ip Vp = 2400Ip (240) = 2400Ip = 2400
240
AC input voltage (i.e)
Voltage after transformer
Voltage after component (i)
Voltage after component (iii)
(i) R (ii) S (iii) P
Ip = 10A (1m)
Is Vs = 2400WIs(12) = 2400
Is = 2400 12
= 200A (1m)
V = I RR = Vs Is
= 12 200= 0.06 Ω (1m)
(4 marks)
20. i) National development ii) Commerce iii) Social interaction (3 marks)21. A, D & E (3 marks)22. C, E & D (3 marks)23. LAND
i) Construction of roadii) Traffic control systemiii) Bridgesiv) Flow of trafficv) Types of vehiclevi) Capacity & weight
AIRi) Construction of Airportsii) Control systemiii) Transportation system in the air port and it surroundingsiv) Capacity & weight
WATERi) Construction of port & jettiesii) Transportation System in ports & jettiesiii) Capacity & weight
Any 3 Answers
(3 marks)
24. A, B & C (3 marks)25. Transportation
SystemLand Air Water
Mode of Transportation
Trishaw Hot Air Balloon Rowing Boat
Advantages
Good for health Low cost maintenance Save fuel Antique Etc.
Decrease the Fuel usage It can overcome land barriers Etc.
Good For Health
Etc.(3 marks)
SKEMA DIAGNOSTIK UPT F4 2006
Section B
a) Work Types Tasks Marks
A (Tapping)
i) Drill = 10 – 1.5 = 8.5 mm (diameter)ii) Use taper tap.iii) Turn wrench clock wise.iv) Turn wrench anti clock wise.v) Use plug tapiv) Use bottoming tap.
1 x 6 = 6
B (Counter Sunk)i) Mark point with centre punch.ii) Drill hole with 10 mm diameter.iii) Enlarge to 12 mm diameter hole with ‘rose’
1 x 3 = 3
C (Groove)i) Mark point C with centre punch.ii) Drill hole with 30 mm diameter.iii) Cut straight line with hacksaw.
1 x 3 = 3
Others Sidei) Clamp the plate.ii) Cut straight line with hacksaw.iii) Filing / Finishing work.
1 x 3 = 3
b) 1. Drill (1 x 5 = 5 marks)2. C-clamp 5. File3. Rose (Drill Bit) 6. Tap4. Hack saw 7. Centre punch
top related